Terraco Terrabond A – 20kg is Terraco’s concentrated acrylic bonding agent, used diluted as a primer/sealer on porous surfaces and as an additive in cement mortars, renders, screeds and tile adhesives. This listing is the 20 kg pack. Al Tashteb Al Saree is an authorised Terraco distributor, supplying Terrabond A from our shop in Bu-Tina, Sharjah, to Dubai, Sharjah, Ajman and the rest of the UAE.
Ask for price and stock on WhatsApp or call +971 52 510 4678.
What is Terraco Terrabond A?
Terrabond A is Terraco’s concentrated acrylic bonding agent (product code 68210). It is an acrylic resin that you dilute with water and use in two ways: brushed or rolled on as a primer/sealer for porous concrete, blocks, plaster and screeds, or added to the gauging water of cement mortars, renders, screeds and tile adhesives. Terraco states that it improves the compressive, tensile and flexural strength of mortars and lowers the water/cement ratio. It is non-toxic, non-flammable and non-crystallising, and works on interior and exterior surfaces.
Because it is highly concentrated, a small jerrican goes a long way: most uses dilute it between 1:2 and 1:10 with water. In the UAE it is the standard primer Terraco specifies under its self-levelling screeds and repair mortars, and a common way to stop a hot, absorbent block wall from sucking the water out of fresh plaster or skim.
Where to use it
- Priming and sealing porous but firm concrete, aerated (AAC) concrete, plaster and screeds
- Bonding coat before patch repairs, plasters and screeds
- Admixture in repair mortars, plasters and screeds
- Admixture in thick-bed and thin-bed tile fixing mortars
- Additive in cement-based paints and lime washes
- Primer under Terraco Terrascreed and Terramix (as their data sheets specify)
Dilution guide
| Use | Terrabond A : water |
|---|---|
| Primer/sealer on porous surfaces | 1:2 to 1:5 (by porosity) |
| Repairs over 5 mm on porous surfaces | 1:5 |
| Repair mortar under 5 mm thick | 1:3 |
| Repairs on firm surfaces | 1:10 |
| Plasters and screeds (standard) | 1:10 |
| Thin-coat mortars | 1:7 |
| Tile fixing, thick bed | 1:5 |
| Tile fixing, thin bed | 1:3 |
| Cement paints and lime washes | 1:5 to 1:10 |
Mortar mix guide
For mortars with a cement content of about 400 kg/m³, Terraco gives these dosages:
| Application | Thickness | Terrabond A (% of cement weight) | Water : Terrabond A |
|---|---|---|---|
| Repairs, porous surface | Over 5 mm | 10% | 5:1 |
| Repairs, porous surface | Under 5 mm | 15–20% | 3:1 |
| Repairs, firm surface | Over 5 mm | 5% | 10:1 |
| Plasters and screeds | Over 5 mm | 5% | 10:1 |
| Plasters and screeds | Under 5 mm | 5–10% | 7:1 |
| Tile fixing | Thick bed | 10% | 5:1 |
| Tile fixing | Thin bed | 15–20% | 3:1 |
Example: a 50 kg bag of cement in a porous-surface repair mix over 5 mm thick takes 10%, so about 5 kg of Terrabond A, mixed into the gauging water at about 5 parts water to 1 part Terrabond A. Dosage figures are Terraco’s; the calculation is ours.
Technical data
| Binder | Acrylic |
| Product code | 68210 |
| Specific gravity | 1.02–1.05 |
| Solids content | About 45% |
| pH | 7.0–9.0 |
| Properties | Non-toxic, non-crystallising, non-flammable |
| Packaging (data sheet) | 4 kg and 20 kg jerricans or pails |
| Shelf life | 12 months unopened |
How to apply
- Clean the surface and remove all loose particles, dust and laitance.
- Dilute Terrabond A with clean water at the ratio for your job (table above).
- As a primer: brush or roll the solution on evenly. Very absorbent surfaces may need 2–3 coats, as Terraco’s screed data sheets advise.
- As an admixture: use the diluted solution as the gauging water for the mortar, screed or tile adhesive.
- For repairs, apply the repair mortar once preparation is complete.
- Clean tools with water before the resin dries.
Storage and safety
- Keep frost-free, in a clean dry area away from direct sun and extreme heat. Shelf life is 12 months unopened; use the oldest stock first.
- Avoid prolonged contact with skin and eyes, and see the safety data sheet for full details.
Frequently asked questions
Is Terrabond A a primer or an additive?
Both. Dilute it and brush it on as a primer/sealer, or dilute it and use it as the mixing water in cement mortars, renders, screeds and tile adhesives.
What ratio do I use under a self-levelling screed?
Terraco’s Terrascreed data sheets call for Terrabond A diluted 1:5 with water, with 2–3 coats on very absorbent floors.
How far does a jerrican go?
Terraco doesn’t publish a coverage rate, because it depends on the dilution and how absorbent the surface is. Tell us the job and area on WhatsApp and we’ll help you estimate it.
Data sheet and related products
- Terrabond A data sheet (PDF, Terraco UAE)
- Terrabond A product page
- Terrascreed GP 100
- Terrascreed EX500
- All Terraco products we supply
Technical data from the Terraco data sheet for Terrabond A. Always check the latest data sheet before specifying.


Reviews
There are no reviews yet.