Terraco Pluggit 311 is Terraco’s rapid-setting, cement-based water-stop mortar (product code 76311) for plugging active leaks and running water in concrete and masonry. Al Tashteb Al Saree is an authorised Terraco distributor, supplying Pluggit 311 from our shop in Bu-Tina, Sharjah, to Dubai, Sharjah, Ajman and the rest of the UAE.
Ask for price and stock on WhatsApp or call +971 52 510 4678.
What is Pluggit 311?
Pluggit 311 is a one-component, dark grey cementitious powder that sets in about 5 minutes, fast enough to stop water that is actively running or seeping through a crack, hole or joint. It is shrinkage-compensated, chloride-free and sets above or below water, so it can be pressed straight into a leaking basement wall, tank or pipe penetration. Once the leak is stopped, the area can be waterproofed or overcoated.
Typical UAE uses are leaks in basement walls and lift pits where the water table is high, water tank and reservoir repairs, leaking pipe and conduit entries, and sealing static cracks and holes in foundations before applying a waterproofing coating.
Where to use it
- Stopping running water or seepage through concrete or masonry
- Filling static cracks and holes in foundations, basements, tunnels and reservoirs
- Water tanks and sewer pipes
- Sealing around pipe penetrations before waterproofing
Technical data
| Type | One-component, rapid-setting cementitious water-stop mortar |
| Product code | 76311 |
| Colour | Dark grey |
| Mixing water | 0.26 L per 1 kg of powder (stiff paste) |
| Yield | 13.5 L of mix per 20 kg with 5.2 L water |
| Initial set | About 5 minutes |
| Final set | About 2 hours (depends on temperature) |
| Compressive strength | > 20 N/mm² at 7 days; > 25 N/mm² at 28 days |
| Flexural strength | > 3 N/mm² at 7 days; > 8 N/mm² at 28 days |
| Tensile strength | > 1 N/mm² at 28 days |
| Consumption | 1.6 kg/m² per mm |
| Maximum thickness | 50 mm vertical; 30 mm overhead |
| Wet density | 1,900 kg/m³ |
| Application temperature | +5 °C to +30 °C |
| Packaging (data sheet) | 5 kg pail (5 × 1 kg) or 20 kg pail (20 × 1 kg) |
| Shelf life | 9 months unopened |
How to apply
- Remove dust, dirt, debris, salts, oil and grease. Protect adjacent surfaces.
- Cut out the crack or hole so the plug can key in, and remove standing water. If the area is dry, dampen it first.
- Mix only what you can use in 1–2 minutes: about 0.26 L of water per 1 kg, to a stiff paste. Never mix for more than 30 seconds.
- Press the paste firmly into the void and hold it in place until it sets, usually 3–5 minutes.
- Once set, trim the excess flush with a trowel or spatula.
- Overcoat with Terraco Weathercoat if required after initial set, and clean tools with water straight away.
How much do you need?
The pails contain individual 1 kg packs, so you can open one at a time. One kilo makes about 0.68 litres of mix (Terraco’s 13.5 L per 20 kg).
| Repair | Approx. volume | Pluggit needed |
|---|---|---|
| Hole 50 × 50 × 50 mm | 0.125 L | about 0.2 kg |
| Crack chased 20 × 20 mm, 1 m long | 0.4 L | about 0.6 kg |
| Pipe entry ring, 100 mm pipe, 25 mm gap, 50 mm deep | about 0.5 L | about 0.7 kg |
Volumes are our calculations from Terraco’s yield figure; allow extra for waste, because the mix sets very quickly.
Safety
- Wear gloves and goggles: it is cement-based and sets fast.
- Store dry, away from direct sun and extreme heat or cold. Shelf life is 9 months unopened.
Frequently asked questions
Will it really set under running water?
Yes. Terraco lists setting above and below water. Press and hold it in the leak until it sets, usually 3–5 minutes.
Is Pluggit a waterproofing coating?
No. It plugs leaks, cracks and holes. Waterproof the area afterwards with a suitable coating.
Why mix so little at a time?
It starts setting in about 5 minutes, so mix only what you can place in 1–2 minutes.
Data sheet and related products
Technical data from the Terraco data sheet for Pluggit 311. Always check the latest data sheet before specifying.


Reviews
There are no reviews yet.