Terraco Terraroc NS 100 is a pre-mixed, non-shrink, chloride-free cementitious grout that can be poured or pumped. It is for anchor bolts, machine and pump bases, manholes, posts, and voids 10–100 mm deep. This listing is the 25 kg bag. Al Tashteb Al Saree is an authorised Terraco distributor, supplying Terraroc NS 100 from our shop in Bu-Tina, Sharjah, to Dubai, Sharjah, Ajman and the rest of the UAE.
Ask for price and stock on WhatsApp or call +971 52 510 4678.
What is Terraroc NS 100?
Terraroc NS 100 is a grey hydraulic grout of graded silica, Portland cement and additives. Being non-shrink, it fills a gap completely and stays in full contact as it hardens. That is what you need under steel base plates, around anchor bolts and in pump and machine plinths, where an ordinary sand/cement mortar would shrink away and leave voids. It flows, so it can be poured or pumped into tight gaps, and it is chloride free, which protects embedded steel from corrosion.
It is fast to gain strength: Terraco gives 25 N/mm² at 1 day, 53.5 N/mm² at 7 days and 64.5 N/mm² at 28 days.
Where to use it
- Grouting anchor bolts and holding-down bolts
- Machine and pump plinths, and under base plates
- Manhole frames, fencing and boundary posts
- Narrow void grouting, and gaps 10–100 mm
- Concrete floor repairs and screeds, bulked with sand or stone
Technical data
| Type | Non-shrink, chloride-free cementitious grout |
| Colour | Grey |
| Grout thickness | 10–100 mm |
| Mixing water | 3.5 L cold water (25 °C) per 25 kg, plus up to 0.5 L more |
| Yield | 12 L per 25 kg bag (80 bags ≈ 1 m³) |
| Compressive strength | 25.0 N/mm² (1 day); 53.5 (7 days); 64.5 (28 days) |
| Flexural strength | 7.3 N/mm² (7 days); 8.9 N/mm² (28 days) |
| Packaging | 25 kg paper bags |
| Shelf life | 6 months unopened |
How to grout
- Prepare: remove dust, dirt, salts, oil, grease and ridges. Saturate the concrete with water for at least 2 hours and remove the excess, or prime with Terrabond A or Epirok EP 1 and place the grout while the primer is wet.
- Form up: seal shuttering so the grout can’t leak.
- Mix: add a 25 kg bag to 3.5 litres of cold water (up to 0.5 L more for extra flow). Mix for 5 minutes.
- Place: pour or pump continuously from one side so air is pushed out. Have enough people to mix and place without stopping. Above 33 °C, place it straight after mixing.
- Finish: trim the edges and float once it has partly set.
- Cure: keep it damp and covered with plastic or damp hessian, or mist it, continuously for 3 days. Use curing compound on exposed vertical faces.
Bulking for screeds and floor repairs
- 20–50 mm: mix 1:1 with 0.6–1.2 mm silica sand.
- Over 50 mm: mix 1:1 with 10 mm graded stone; the stone should not exceed one-third of the final thickness.
- Bulked mixes use 4.5–5.0 L water per 50 kg of mix.
How much do you need?
Each bag yields about 12 litres. Example: grouting under a 600 × 600 mm base plate at 40 mm deep is about 14.4 litres plus edges, so allow 2 bags. For 1 m³ you need about 80 bags.
Storage and safety
- Store dry and out of sun and extreme temperatures. Shelf life is 6 months unopened.
- Cement-based: wear gloves and eye protection.
Frequently asked questions
Is it non-shrink?
Yes. Terraco describes it as a non-shrink, chloride-free grout.
Can I use hot water?
No. Use cold water (about 25 °C). In UAE summers, keep bags and water in the shade and grout in the cooler hours.
How strong is it?
64.5 N/mm² compressive at 28 days, and 25 N/mm² after just 1 day.
Data sheet and related products
Technical data from the Terraco data sheet for Terraroc NS 100. Always check the latest data sheet before specifying.


Reviews
There are no reviews yet.