Terraco 20 kg Terracrete – Grey is Terraco’s two-component, elastomeric cementitious waterproof slurry for wet rooms, swimming pools, non-potable water tanks, foundations and retaining walls. Tiles can be fixed directly onto it. This listing is grey, the 20 kg kit pack. Al Tashteb Al Saree is an authorised Terraco distributor, supplying Terracrete from our shop in Bu-Tina, Sharjah, to Dubai, Sharjah, Ajman and the rest of the UAE.
Grey is the usual choice under tiles and on below-ground and structural work.
Ask for price and stock on WhatsApp or call +971 52 510 4678.
What is Terraco Terracrete?
Terracrete is Terraco’s elastomeric, polymer-modified cementitious waterproof slurry. It is a two-component system: an acrylic resin that is highly resistant to alkalinity, and a powder of special hydraulic cements, graded fillers and performance additives. The two are mixed on site at a fixed ratio, with no added water, and brushed, broomed or sprayed onto concrete and masonry to form a seamless, flexible waterproof lining.
Terracrete is vapour permeable, so the structure can breathe while liquid water is kept out. It is non-toxic, resists UV and weather, and has good anti-carbonation properties. Cement mortars and tile adhesives bond directly to it, which is why it is widely used under tiles in wet rooms and pools. Terraco especially recommends it for wet rooms, reservoirs, and below-DPC tanking behind EIFS.
Where to use it
- Waterproof lining of non-potable water tanks and reservoirs
- Swimming pools, decorative ponds and planter boxes
- Wet room walls and floors: bathrooms, showers, kitchens and laundries
- Retaining walls and foundations
- Water channels, irrigation canals, concrete gutters and patios
- Filling blow holes and pores in concrete, hairline crack repair and low-build concrete repairs
Don’t apply Terracrete over bituminous coatings, or while temperatures are rising (out-gassing can cause pinholes). Outside, don’t apply if rain is likely within 24 hours.
Technical data
| Type | Two-component elastomeric cementitious waterproof slurry |
| Mix ratio | 1 part resin : 3 parts powder by weight; no water added |
| Colours | Grey and natural white |
| Kit | 20.25 kg pail: 5 kg resin, 15 kg powder and 0.25 kg Terrabond A; yield 10.8 L |
| Coats | 2–3, each 0.75–1.0 mm |
| Total thickness | 1.5 mm under tiles; 2.0 mm where exposed |
| Consumption | 2.8–3.8 kg/m² of mixed Terracrete |
| Pot life (30 °C) | 2 hours |
| Surface dry (30 °C) | Under 3 hours |
| Overcoat time (30 °C) | 6 hours minimum |
| Tiling | After at least 3 days |
| Flood test | After at least 7 days’ curing |
| Adhesion (ASTM D4541) | > 0.75 N/mm² |
| Crack bridging (EN 14891) | > 0.75 mm |
| Elongation | Up to 5% |
| Water penetration, 5 bar, 72 h (DIN 1048-5 / EN 12390-8) | Nil |
| Water pressure resistance, 1.5 bar (EN 14891) | Nil |
| Vapour permeability (sd) | 0.16 m |
| VOC | < 5 g/l |
| Application temperature | 5 °C to 40 °C; not above 80% humidity |
| Shelf life | At least 12 months in sealed packaging |
Preparing the surface
- The background must be clean and sound. Remove old coatings, cement laitance, unsound honeycombing and spalling concrete mechanically.
- Remove dust and loose material by brush, broom or vacuum. Grind off ridges and sharp projections, and remove oil, grease and anything else that stops adhesion.
- Mortar joints must be sound and flush with the blockwork. Make good cracks and defects with a suitable Terraco repair product, and form fillets at wall–floor corners.
- Reinforce wall–floor corners, pipe entries and drains with Terratape or Terraco Joint Reinforcing Strip.
- Prime dry, porous backgrounds with Terrabond A diluted 1:3 with clean water (a bottle comes in the kit), or with undiluted Terraco Waterproofing Primer. Otherwise saturate the background with water, leaving no standing water.
Mixing and application
- Mix full kits only. Pour the resin into a clean vessel and slowly add the powder.
- Mix for at least 3 minutes with a slow-speed mixer (200–600 rpm), keeping the blade below the surface to avoid trapping air, until smooth and lump-free.
- Stand for at least 5 minutes, then remix for 30 seconds. Never add water to adjust or re-temper the mix.
- Apply 2–3 coats by brush or broom, each coat at right angles to the last, at 0.75–1.0 mm per coat. Build to 1.5 mm under tiles or 2.0 mm on exposed surfaces.
- Leave at least 6 hours between coats. Stir occasionally while working to keep the aggregate in suspension.
- Protect from wind and direct heat while it cures. In UAE summers, work early in the morning or in shade, not while the surface is heating up.
- Tile after at least 3 days, using a suitable adhesive such as Terrafix W32. Flood test after at least 7 days.
- Clean tools with water straight away.
How much do you need?
Each kit gives 20 kg of mixed material (5 kg resin + 15 kg powder). At Terraco’s 2.8–3.8 kg/m², one kit covers about 5.3–7.1 m² at the full system thickness.
Example: a 4 m² shower floor plus 8 m² of shower walls (12 m²) needs about 34–46 kg, so allow 3 kits. Areas are calculated from Terraco’s consumption figure; rough backgrounds use more.
Storage and safety
- Store in the original sealed packaging in a clean, dry place, away from humidity, moisture, direct sun and extreme heat or cold. Use the oldest stock first.
- Avoid prolonged contact with skin and eyes. If it gets in your eyes, rinse with clean water and get medical treatment. See the latest safety data sheet.
Frequently asked questions
Can I tile directly onto Terracrete?
Yes. Cement mortars and tile adhesives bond directly to it. Build 1.5 mm total thickness and wait at least 3 days.
Is it safe for drinking water tanks?
The data sheet lists non-potable water tanks and reservoirs. For drinking water, check the approvals you need with us before buying.
How long before I can fill a pool or flood test?
Cure for at least 7 days first.
Terracrete or Weathercoat GP?
Both are cement-acrylic two-component waterproofers. Terracrete is a fixed-ratio slurry system with published test data for tanking, pools and wet rooms. Weathercoat GP can be mixed as a coating, slurry or screed. See Terracrete vs Weathercoat GP.
Data sheet and related products
- Terracrete technical data sheet (PDF, Terraco UAE)
- Terracrete product page
- All Terraco products we supply
Technical data from the Terraco UAE data sheet for Terracrete. Always check the latest data sheet before specifying.






Reviews
There are no reviews yet.