Terraseal Grey Kit – 20kg

Terraseal Grey Kit – 20kg, available from Al Tashteb Al Saree in Bu-Tina, Sharjah. Ask for price and stock on WhatsApp or call us.

WhatsApp usCall now

SKU: ATS-TER-B005561 Category:
Request a quote
Please enable JavaScript in your browser to complete this form.
Tell us the quantity needed, or the area to be covered.
Brand, size, colour or other details that help us prepare your quote.

Terraseal Grey Kit – 20kg is Terraco’s two-component, polymer-modified cementitious waterproofing coating (code 68637), used as a moisture barrier on concrete and masonry behind EIFS facades and curtain walls. This listing is the grey 20 kg kit (5 kg resin + 15 kg powder). Al Tashteb Al Saree is an authorised Terraco distributor, supplying Terraseal from our shop in Bu-Tina, Sharjah, to Dubai, Sharjah, Ajman and the rest of the UAE.

Ask for price and stock on WhatsApp or call +971 52 510 4678.

What is Terraseal?

Terraseal is a kit of an alkali-resistant acrylic resin and a powder of special cements, graded fillers, wetting agents and adhesion promoters. Mixed together (no water added), they form a flexible, seamless, tough waterproof coating that still lets the wall breathe, because it is vapour permeable. Terraco designed it to waterproof the substrate before Terraco EIFS or non-load-bearing assemblies such as curtain walls are installed, so rain that gets behind the cladding can’t soak into the wall.

Terraco reports more than 90% reduction in water absorption (ASTM D870), adhesion of at least 0.5 N/mm² (ASTM D4541), an ASTM E-84 Class A surface burning rating, and VOC below 5 g/l.

Where to use it

  • Waterproofing concrete and masonry walls before Terraco EIFS
  • Behind curtain walls and other non-load-bearing facade assemblies
  • Waterproofing cement fibre boards

It is not designed for continuous water immersion (tanks, pools) and must not go on bituminous coatings. For water-retaining structures, see Terracrete.

Technical data

TypeTwo-component polymer-modified cementitious waterproof coating
Product code68637
Kit20 kg: 5 kg resin jerrican + 15 kg powder bag
Mixing ratio1 resin : 3 powder by weight (full kits only, no water)
Yield10.5 L per 20 kg kit
ConsumptionAbout 1.9–2.9 kg/m² (mixed)
Coats / thicknessAt least 2 coats at right angles; 0.5–1.0 mm per coat; 1.0–1.5 mm total
Pot life2 hours at 30 °C; apply within 1 hour of mixing
Overcoat timeAt least 6 hours at 30 °C
Surface dryUnder 3 hours at 30 °C
ColoursGrey and natural white
Specific gravity1.85 ± 0.05
Shelf lifeAt least 12 months sealed

How much do you need?

At 1.9–2.9 kg/m², one 20 kg kit covers about 7–10.5 m² for the full two-coat system. Example: a 50 m² wall behind cladding needs about 95–145 kg, so allow 5–8 kits, nearer the top on rough blockwork. Based on Terraco’s consumption figure.

Preparing the surface

  1. The substrate must be clean and sound. Mechanically remove old coatings, laitance and unsound, honeycombed or spalled concrete.
  2. Brush, sweep or vacuum off dust and loose material, and grind off ridges and sharp projections.
  3. Remove flaking material, oil, grease and anything that stops adhesion.
  4. Rinse and apply to a damp (water-saturated) surface with no standing water.

Mixing and application

  1. Mix full kits only. Add the powder slowly to the resin and mix for at least 3 minutes at 200–600 rpm, keeping the paddle below the surface.
  2. Let it stand for at least 5 minutes, then mix again for 30 seconds. Don’t add water, and stir occasionally while you work.
  3. Brush on (smooth surfaces) or spray (uneven surfaces and blockwork; ask Terraco’s technical team about spray set-up). Press it firmly into the surface to fill pinholes, cracks and honeycombing.
  4. Let the first coat dry at least 6 hours, then apply the second coat at right angles to the first, for 1.0–1.5 mm total.
  5. Protect it from wind and direct heat while it cures. Clean tools with water immediately; hardened material can only be removed mechanically.

UAE site conditions

  • Don’t apply when humidity is above 80%, which is common on the coast on summer mornings and evenings.
  • Don’t apply while the temperature is rising (risk of outgassing and pinholes), so avoid sun-facing walls in the morning heat-up.
  • Don’t apply if rain is expected within 24 hours: it isn’t water-resistant until fully dry.
  • The data sheet’s application temperature range appears to be 5–40 °C; confirm it with us or Terraco for hot-weather work.

Storage and safety

  • Store in a clean, dry area away from humidity, moisture, direct sun and extreme heat or cold. Use the oldest stock first.
  • Cement-based and alkaline (pH 11–13): avoid prolonged skin and eye contact; rinse with clean water and seek medical advice if needed.

Frequently asked questions

Can I use Terraseal for a water tank or roof?

No. It is not designed for continuous immersion. Look at Terracrete for wet areas and tanks, or Maxi Roof Coating for roofs.

Why is it vapour permeable?

So moisture inside the wall can escape while rain from outside is kept out, which matters behind insulation and cladding.

Data sheet and related products

Technical data from the Terraco UAE data sheet for Terraseal. Always check the latest data sheet before specifying.

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Shopping Cart
Scroll to Top