Terraco Weathercoat Seal is a one-component, fluid-applied, highly flexible acrylic water-resistive and air barrier. It goes on the sheathing boards behind Terraco EIFS facade systems, and on masonry behind metal panel cladding, to stop wind-driven rain and air getting into the wall. Al Tashteb Al Saree is an authorised Terraco distributor, supplying Weathercoat Seal from our shop in Bu-Tina, Sharjah, to Dubai, Sharjah, Ajman and the rest of the UAE.
Ask for price and stock on WhatsApp or call +971 52 510 4678.
What does an air and water barrier do?
In a modern facade, the outer finish (EIFS render or metal panels) sheds most of the rain, but some water and air always gets behind it, through joints, fixings and wind pressure. A water-resistive barrier is a continuous membrane on the wall behind the cladding. It stops that water reaching the board or blockwork, and it cuts air leakage, which matters for comfort and air-conditioning load in UAE buildings. Weathercoat Seal does this as a liquid, so it forms a seamless layer with no laps to fail, and it follows corners, openings and board joints that sheet membranes find hard to seal.
Where to use it
- Terraco-approved exterior gypsum and cement board sheathing behind Terraco EIFS
- Precast concrete, concrete block and other masonry
- Behind metal panel cladding
- Low- and high-rise residential and commercial buildings
Not for water immersion. It is a wall barrier, not tanking. For tanks, pools and wet rooms, use Terracrete.
Technical data
| Type | One-component fluid-applied water-resistive and air barrier |
| Product code | 64234 |
| Binder | Acrylic |
| Colours | Blue and red |
| Specific gravity | 1.42 ± 0.05 |
| Dilution | None: ready to use |
| Application | Roller or brush, 2 coats; or stainless-steel trowel, 1 coat |
| Wet film (roller) | 1st coat 300–350 microns; 2nd coat 250–300 microns |
| Thickness (trowel) | About 0.6 mm, one coat |
| Coverage | About 0.6–1.1 kg/m² |
| Application temperature | 5 °C to 40 °C |
| Packaging | 25 kg pail |
| Shelf life | 12 months unopened |
Performance
| Property | Standard | Result |
|---|---|---|
| Surface burning characteristics | ASTM E84 | Class A |
| Water vapour transmission | ASTM E96/E96M-16 | < 1.0 perms |
| Water resistance, 24 h immersion | ASTM D2247-15 | No effect |
| Adhesive strength | – | ≥ 2.0 N/mm² |
| VOC | – | < 5 g/l |
As stated by Terraco.
How to apply
- Remove dust, dirt and foreign matter. The background must be free of salts, oil, grease and ridges.
- Treat the details first: embed Terraco-approved sheathing tape over board joints, edges, corners and fixing points.
- After 4–6 hours, coat the whole surface: two roller or brush coats at the wet film thicknesses above, or one trowel coat of about 0.6 mm.
- Let it dry fully (3–4 days, depending on climate) before the next layer of the system goes on.
- Don’t apply if rain is expected within 24 hours. Clean tools with water.
The blue and red colours make it easy to check full, even coverage before the wall is closed in.
How much do you need?
At about 0.6–1.1 kg/m², one 25 kg pail covers roughly 23–42 m². Example: a 300 m² facade at the upper rate needs about 330 kg, so allow 14 pails. Areas are calculated from Terraco’s coverage figure.
Storage and safety
- Store in a clean, dry area away from direct sunlight and extreme heat and cold. Shelf life is 12 months unopened.
- Avoid prolonged contact with eyes and skin, and see the safety data sheet.
Frequently asked questions
Can I use it on a roof or in a pool?
No. Terraco says not to use it in water immersion areas. It is a wall barrier.
Do I need to thin it?
No. It is ready to use.
How long before the next layer?
Allow full drying, 3–4 days depending on climate.
Is it part of the EIFS system?
Yes. It is used on sheathing boards behind Terraco EIFS. See EIFS Alpha vs Perma vs Polar.
Data sheet and related products
- Weathercoat Seal technical data sheet (PDF, Terraco UAE)
- Weathercoat Seal product page
- All Terraco products we supply
Technical data from the Terraco UAE data sheet for Weathercoat Seal. Always check the latest data sheet before specifying.






Reviews
There are no reviews yet.