Terraco EIFS Polar (XPS) System is Terraco’s external insulation and finish system built on extruded polystyrene (XPS) boards, suited to hot, humid climates with air-conditioned interiors. Al Tashteb Al Saree is an authorised Terraco distributor, supplying EIFS Polar components from our shop in Bu-Tina, Sharjah, to Dubai, Sharjah, Ajman and the rest of the UAE.
Ask for a system quote on WhatsApp or call +971 52 510 4678.
What is EIFS Polar?
Polar uses XPS boards as the insulation layer. Terraco recommends it for hot, humid countries where buildings are air-conditioned inside, which describes most of the UAE coast. XPS has low vapour permeability, which Terraco says reduces condensation risk when cool, dry indoor air meets hot, humid outdoor air. Terraco also cites enhanced mechanical properties, making Polar suitable for high-traffic areas and for places where thinner insulation is needed, such as around windows and doors.
System build-up
- Adhesive: Styrofix
- Insulation: XPS boards, thickness chosen for the required U-value
- Mechanical fixing: plastic or steel pin dowels
- Basecoat: Styrobond DP with Terramesh glass-fibre mesh, 3–5 mm overall
- Primer: Terraco P Primer
- Finish: Terracoat, Terralite or Terol decorative coating
Thermal performance
| XPS thermal conductivity (K) | 0.030 W/(m·K) |
| U-value at 100 mm | 0.30 W/(m²·K) |
Values are indicative and vary with board specification; your consultant should confirm the thickness for the project.
Fire safety
Terraco’s brochure does not state a fire rating for Polar. In the UAE, facade systems must meet the UAE Fire and Life Safety Code, so confirm the specification with your consultant and Civil Defence before ordering. Where a higher fire rating is required, Terraco recommends EIFS Perma (mineral wool).
Guarantee and approvals
The system is covered by the Terraco International Guarantee under the same conditions as Alpha: finished with a listed Terraco decorative coating and installed by an Approved Terraco EIFS Applicator. Terraco lists approvals for its EIFS range including EOTA ETAG 004, BBA, NSAI and UAE approvals.
Where to use it
- Air-conditioned buildings in hot, humid coastal climates
- High-traffic, impact-prone lower facades
- Window and door reveals where thinner insulation is needed
Frequently asked questions
Why XPS instead of EPS?
XPS has lower vapour permeability and better mechanical properties, according to Terraco, which helps against condensation in humid, air-conditioned buildings and in high-traffic areas. EIFS Alpha (EPS) is the general-purpose alternative.
Can you quote a full system?
Yes. Send the wall area, required U-value and finish on WhatsApp, and we’ll put together the components with Terraco.
Polar vs Alpha vs Perma at a glance
| Polar | Alpha | Perma | |
|---|---|---|---|
| Insulation | XPS | EPS / graphite G-EPS | Mineral wool |
| Thermal conductivity | 0.030 W/(m·K) | 0.033 / 0.030 W/(m·K) | 0.040 W/(m·K) |
| U-value at 100 mm | 0.30 W/(m²·K) | 0.33 / 0.30 W/(m²·K) | 0.40 W/(m²·K) |
| Vapour permeability | Low | Moderate | High (breathable) |
| Best for | Hot, humid, air-conditioned buildings; impact-prone areas | General new build and renovation | Higher fire rating, breathable walls |
Figures are from the Terraco EIFS brochure and are indicative.
Why Polar suits the UAE coast
In Dubai, Sharjah and Abu Dhabi, buildings are cooled almost all year while the outside air is hot and often very humid. Moisture tends to push from the hot outside toward the cool inside. XPS has low vapour permeability, which Terraco says reduces the risk of that moisture condensing within the wall. Its closed-cell structure and higher compressive strength also make it tougher on lower facades, podiums and around windows and doors, where thinner but robust insulation is useful.
Choosing board thickness
At 0.030 W/(m·K), 100 mm of XPS gives a U-value of about 0.30 W/(m²·K). Agree the target U-value with your consultant and check it against Dubai Green Building Regulations or Estidama requirements where they apply; Terraco’s tables also cover 50, 150 and 200 mm boards.
Good practice on site
- XPS boards are smooth; roughen or use boards with a keyed surface so the adhesive and basecoat bond well.
- Fix with Styrofix plus plastic or steel pin dowels as Terraco specifies.
- Embed Terramesh fully in Styrobond DP at 3–5 mm overall, with diagonal patches at opening corners.
- Protect boards from long UV exposure before the basecoat goes on.
- Installation by an Approved Terraco EIFS Applicator is a condition of the Terraco International Guarantee.
Data sheets and related products
System details from the Terraco EIFS brochure. Always check the latest Terraco documentation before specifying.






Reviews
There are no reviews yet.